New windows and doors improve comfort, cut energy bills and add long-term value to your home. Meridian Windows and Doors Fort Worth pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
PGT Patio Door Installation in Fort Worth: What to Know First
PGT patio door installation in Fort Worth typically runs $1,800 to $4,600 depending on the door line, glass package, and what the existing opening needs. We are an independent PGT service provider, not a factory-authorized dealer, and we install the full range of PGT sliding and hinged patio doors with a written price before the first screw turns. Most single-door installs take one day on site. If you own a PGT door that leaks, binds, or won’t lock and you want a straight answer on whether it should be repaired or replaced, call (682) 708-0962. This page is for Fort Worth homeowners who already have PGT product or are spec’ing it and want installation done right the first time.
How PGT Products Fail – and How We Fix Them
PGT builds a solid door, but Fort Worth’s heat, clay soil movement, and spring storm cycles expose real weaknesses. These are the failures we see most often on PGT patio door installations across Fort Worth, from Wedgwood to Ryan Place to newer developments off Chisholm Trail Parkway:
- PGT 5500 Series slider roller wear in sandy soil areas. Homes near the Trinity River and in southwest Fort Worth deal with fine grit that works into the bottom track. The factory nylon rollers wear flat, the door drags, and homeowners assume the frame warped. We replace rollers, clean and square the track, and set the door to glide on PGT-spec rollers rather than forcing a generic part that grinds the rail.
- PGT WinGuard impact door seal compression loss. WinGuard doors carry a heavy laminated glass panel. Over five to eight years, the weatherstripping compresses unevenly, especially on west-facing exposures where afternoon heat bakes the gasket. You’ll feel a draft at the interlock, or see daylight at the corner. We strip and re-gasket the panel, then check the interlock gap against PGT’s published tolerances rather than guessing.
- PGT 7700 Series multi-point lock misalignment. The 7700 uses a multi-point lock that throws bolts into the header and sill. Foundation movement in North Texas, which is a fact of life on the expansive clay soils common in Fort Worth, shifts the frame a few millimeters. The handle turns hard, or the bolts won’t throw at all. We re-square the door within the rough opening, adjust the keepers, and restore the lock throw without drilling new holes in the frame.
- Weep hole clogging on PGT sliding doors with low sill tracks. PGT’s low-profile sills drain through small weep channels. Pollen, dirt, and oak tassel debris from mature Fort Worth trees plug those holes. Water pools in the track, then wicks under the sill pan and into the subfloor. We clear the weeps, verify the sill pan is flashed correctly, and test drainage with a water bottle before we call the job done.
- Fogged glass on older PGT insulated units. PGT doors built before roughly 2010 shipped with a desiccant seal system that eventually fails in high-humidity Gulf air patterns that reach Fort Worth. You’ll see condensation between the panes that won’t wipe off. We order a replacement insulated glass unit spec’d to the original dimensions, install it under the original warranty-safe perimeter, and don’t try to reseal a failed unit, because that repair doesn’t hold.
Our PGT Patio Door Installation Process
Elliot Vance and our install crew follow a fixed sequence on every PGT patio door job in Fort Worth. No shortcuts, no change orders hiding in the process:
- 1
Call and conversation. You reach a live person at (682) 708-0962. We ask what the door is doing, which PGT line it is if you know it, and what the opening looks like. We schedule a site visit when it suits you. No arrival windows that waste half your day.
- 2
On-site measurements and diagnosis. We measure the rough opening, check the existing frame for square, and look at the sill, the header, and the flashing. If it’s a repair, we identify the failure before we recommend anything.
- 3
Written price. The price goes on paper before any work starts. It includes the door or parts, labor, disposal of the old unit, and any flashing or trim work the opening needs. The number does not move at the door.
- 4
Parts decision. We use PGT OEM parts where the manufacturer’s warranty and fit demand it. Where a quality aftermarket part performs identically at a better price, we tell you and put the choice in writing. We never quietly swap in a cheaper part and call it the same repair.
- 5
Installation and sealing. Our background-checked, uniformed technicians remove the old door, set the new or repaired panel, flash the opening to shed water, and seal every penetration. The seal either holds or it doesn’t – we make sure it holds.
- 6
Test and walkthrough. We cycle the door, test the lock, run water over the exterior, and show you what we did before we leave the driveway. The job is covered in writing for 365 days through our Done Right Promise. If it fails, we come back at no charge.
What PGT Patio Door Installation Costs in Fort Worth
You should know the honest price ranges before you decide anything. These are installed prices for Fort Worth homes, including labor, disposal, and sealing, not bare door prices:
- PGT 5500 Series sliding door, standard glass: $1,800 to $2,800 installed
- PGT 7700 Series sliding door, Low-E glass: $2,600 to $3,900 installed
- PGT WinGuard impact sliding door: $3,200 to $4,600 installed
- PGT hinged patio door, 5500 or 7700 line: $2,200 to $3,500 installed, depending on glass and finish
- Existing PGT door repair and reinstallation: $350 to $900, depending on the failure
What moves the price: rough-opening size, whether the existing flashing is salvageable, glass package (Low-E is a thin coating that reflects heat while letting light through), and whether the frame needs re-squaring due to foundation movement. Call (682) 708-0962 and we’ll give you a written line-item quote for your exact door. Estimates are free.
Why Fort Worth Homeowners Call Meridian Windows and Doors Fort Worth for PGT Work
Meridian Windows and Doors is the windows-and-doors specialist within the Garrison Partners network, operating to The Garrison Standard since 2009. That means every job gets a written price before work begins, every technician is background-checked and uniformed, and every installation carries our 365-Day Done Right Promise. If it’s not done right, we make it right, in writing, for a full year, no fine print about labor. Phones are answered by a live person around the clock, every day. And because we carry eight manufacturer lines, including CGI, CWS, ES Windows, and ECO Window Systems, we’ll never force a PGT product into a job where a different door serves you better, and we’ll never push a replacement when a repair is the honest call.
FAQs
Installing a new PGT door through an independent contractor can affect the factory warranty, which is why we recommend reviewing your warranty terms before any replacement work. For existing doors we repair, we preserve the warranty-safe perimeter and use OEM parts where the manufacturer’s terms require them. Call (682) 708-0962 and we’ll walk you through what your specific PGT warranty says, in plain English, before you commit to anything.
Most PGT patio door installations in Fort Worth are completed in one day on site once the door or parts arrive. Lead time on the door itself depends on the model and glass package, usually one to three weeks from order. We’ll give you a written schedule with your quote so you know exactly when we’re on site and when we’re done.
Repair is usually the better call if the frame is square, the glass is intact, and the failure is a worn roller, compressed seal, misaligned lock, or clogged weep system. Replacement makes sense when the frame has twisted from Fort Worth clay soil movement, the glass seal has failed, or the cost of the repair approaches half the cost of a new door. We’ll tell you the straight answer, not the one that makes us a bigger sale.
Low-E glass is a thin metallic coating applied to the glass surface that reflects heat while letting light through. In Fort Worth, where summer sun pounds west-facing doors, Low-E lowers cooling load and protects interior finishes from UV fading. It costs more than standard glass, which is why we put the exact number on your written quote rather than hiding it in the fine print. Call (682) 708-0962 for a free estimate with both glass options priced out.
The 365-Day Done Right Promise covers every installation and repair we perform for a full year from the completion date. If the work fails within that period, we come back at no charge. The promise is written on every job, with no labor exclusions, no prorating, and no arguing about what “done right” means. A meridian is a fixed line you measure everything against, and that is what the name means and how we run every install.
Ready to get your PGT patio door installed or repaired in Fort Worth? Call (682) 708-0962 for a free, written estimate. A live person answers the phone, and your price will be on paper before any work starts.
Written by Elliot Vance, Owner, Meridian Windows and Doors Fort Worth at Meridian Windows and Doors Fort Worth, serving Fort Worth and nearby areas.
Six Reasons Homeowners Choose Meridian Windows and Doors Fort Worth
Laminated glass and reinforced frames hold up to wind-driven rain, hail and flying debris, so your openings stay sealed when the weather turns.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Tighter seals and insulated glass even out hot and cold rooms and stop the drafts at the frame.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.